Linux系統通過手機GPRS無線上網

2020-07-08 13:09:25

字體：大中小

供稿：網友

首先，要有一臺具備GPRS且?guī)в衜odem功能的手機，以下以palm treo 650為例。

650是不帶modem功能，要通過軟件實現，下載 USB modem軟件并安裝在650上。該軟件支持藍牙和usb數據線兩種模式!

下面首先看系統是否能檢測到modem

sudo wvdialconf

Editing `/etc/wvdial.conf'.Scanning your serial ports for a modem.Modem Port Scan<*1>: S0 S1 S2 S3 WvModem<*1>: Cannot get information for serial port.ttyACM0<*1>: ATQ0 V1 E1 -- OKttyACM0<*1>: ATQ0 V1 E1 Z -- OKttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OKttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OKttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OKttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OKttyACM0<*1>: Modem Identifier: ATI -- ENZOttyACM0<*1>: Speed 4800: AT -- OKttyACM0<*1>: Speed 9600: AT -- OKttyACM0<*1>: Speed 19200: AT -- OKttyACM0<*1>: Speed 38400: AT -- OKttyACM0<*1>: Speed 57600: AT -- OKttyACM0<*1>: Speed 115200: AT -- OKttyACM0<*1>: Speed 230400: AT -- OKttyACM0<*1>: Speed 460800: AT -- OKttyACM0<*1>: Max speed is 460800; that should be safe.ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OKFound an USB modem on /dev/ttyACM0.Modem configuration written to /etc/wvdial.conf.ttyACM0: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"

如果出現以下信息則能檢測modem且將配置自動寫入 /etc/wvdial.conf文件。你modem的設備文件為/dev/ttyACM0

由于配置文件為普通撥號而建立，所以不適合grps撥號，要作以下修改

[Dialer defaults]Init1 = at+cgdcont=1,"ip","cmwap"Modem Type = USB ModemISDN = 0Phone = *99***1#Modem = /dev/ttyACM0Username = anyCarrier Check = noPassword = anyBaud = 460800

保存后，使用wvdial撥號

sudo wvdial

使用超級用戶操作，不然無法會提示設備忙，或更改用戶權限。

--> WvDial: Internet dialer version 1.60--> Cannot get information for serial port.--> Initializing modem.--> Sending: at+cgdcont=1,"ip","cmwap"at+cgdcont=1,"ip","cmwap"OK--> Modem initialized.--> Sending: ATDT*99***1#--> Waiting for carrier.ATDT*99***1#CONNECT~[7f]}#@!}![06]} }<}!}$}%}"}&} } } } }#}$!}![06]} }<}!}$}%}"}&} } } } }#}$@#}%}&}$^[7f]o}'}"}(}"Q}+~--> PPP negotiation detected.--> Starting pppd at Sat Jan 19 10:56:20 2008--> Pid of pppd: 6967--> Using interface ppp0--> pppd: (m[07][08]hr[07][08]--> pppd: (m[07][08]hr[07][08]--> pppd: (m[07][08]hr[07][08]--> pppd: (m[07][08]hr[07][08]--> pppd: (m[07][08]hr[07][08]--> local IP address 10.216.91.90--> pppd: (m[07][08]hr[07][08]--> remote IP address 10.216.91.0--> pppd: (m[07][08]hr[07][08]

到如已經成功啦！我們再來看看路由表

$ routeKernel IP routing tableDestination Gateway Genmask Flags Metric Ref Use Iface10.216.91.0 * 255.255.255.255 UH 0 0 0 ppp0192.168.0.0 * 255.255.255.0 U 0 0 0 wlan0default 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0

因?yàn)槲疫@里還連接到無線網絡，所以默認網關是 192.168.0.1，如果只有GPRS撥號連接，則信息會是：

$ routeKernel IP routing tableDestination Gateway Genmask Flags Metric Ref Use Iface10.216.91.0 * 255.255.255.255 UH 0 0 0 ppp0default 10.216.91.90 0.0.0.0 UG 0 0 0 ppp0

此時，只需設置代理即可以上網了代理為 10.0.0.172:80

由于移動限制了瀏覽器，必須要將瀏覽器頭信息更改才能正常上網。不過已經可以上Q。MSN等聊天工具啦!!

上一篇：手動編譯安裝Linux網卡驅動

下一篇：linux grep搜索命令的使用方法