Enter password: Console> (enable) set system name 5509-ER-F1 System name set. 5509-ER-F1> (enable) set system location 1st Floor Equipment Room System location set. 5509-ER-F1> (enable) set system contact sysadmin@bigcorp.com System contact set. 5509-ER-F1> (enable) set time 04/30/1999 9:30:00 Fri APR 30 1999, 09:30:00 5509-ER-F1> (enable) set password Enter old password: Enter new password: Retype new password: Password changed. 5509-ER-F1> (enable) set enablepass Enter old password: Enter new password: Retype new password: Password changed. 5509-ER-F1> (enable) set banner motd % 5509-ER-F1 (Catalyst 5509) access Restricted % MOTD banner set 5509-ER-F1> (enable) set interface sc0 10.10.1.10/24 Interface sc0 IP address set. 5509-ER-F1> (enable) set ip route default 10.10.1.1 Route added. 5509-ER-F1> (enable) set ip dns server 10.10.10.100 10.10.10.100 added to DNS server table as primary server. 5509-ER-F1> (enable) set ip dns domain bigcorp.com Default DNS domain name set to bigcorp.com 5509-ER-F1> (enable) set ip dns enable DNS is enabled 5509-ER-F1> (enable) set vtp domain BigCorp mode server VTP domain BigCorp modified 5509-ER-F1> (enable) set vlan 10 name Corporate Vlan 10 configuration sUCcessful 5509-ER-F1> (enable) set vlan 20 name DevEng Vlan 20 configuration successful 5509-ER-F1> (enable) set vlan 30 name Mfg Vlan 30 configuration successful 5509-ER-F1> (enable) set vlan 40 name QA Vlan 40 configuration successful 5509-ER-F1> (enable) set vlan 50 name Finance&Admin Vlan 50 configuration successful 5509-ER-F1> (enable) set vlan 60 name Sales&Mktg Vlan 60 configuration successful 5509-ER-F1> (enable) set module name 1 Supervisor III Module name set. 5509-ER-F1> (enable) set port flowcontrol 1/1-2 send off Ports 1/1-2 flow control send administration status set to off (ports will not send flowcontrol to far end) 5509-ER-F1> (enable) set port flowcontrol 1/1-2 receive off Ports 1/1-2 flow control receive administration status set to off (ports will not allow far end to send flowcontrol) 5509-ER-F1> (enable) set port negotiation 1/1-2 enable Ports 1/1-2 negotiation enabled 5509-ER-F1> (enable) set port name 1/1-2 GEC 802.1Q Trunk Ports 1/1-2 name set. 5509-ER-F1> (enable) set port channel 1/1-2 desirable Port(s) 1/1-2 channel mode set to desirable. 5509-ER-F1> (enable) set trunk 1/1 desirable dot1q Port(s) 1/1 trunk mode set to desirable. Port(s) 1/1 trunk type set to dot1q. 5509-ER-F1> (enable) set module name 3 RSM (RSM-ER-F1) Module name set. 5509-ER-F1> (enable) set module name 5 Fast Ether Uplinks Module name set. 5509-ER-F1> (enable) set port name 5/1-4 FEC ISL Trunk Ports 5/1-4 name set. 5509-ER-F1> (enable) set port speed 5/1-4 100 Ports 5/1-4 transmission speed set to 100Mbps. 5509-ER-F1> (enable) set port duplex 5/1-4 full Ports 5/1-4 set to full-duplex. 5509-ER-F1> (enable) set port flowcontrol 5/1-4 send off Ports 5/1-4 flow control send administration status set to off (ports will not send flowcontrol to far end) 5509-ER-F1> (enable) set port flowcontrol 5/1-4 receive off Ports 5/1-4 flow control receive administration status set to off (ports will not allow far end to send flowcontrol) 5509-ER-F1> (enable) set port negotiation 5/1-4 enable Ports 5/1-4 negotiation enabled 5509-ER-F1> (enable) set port channel 5/1-4 desirable Port(s) 5/1-4 channel mode set to desirable. 5509-ER-F1> (enable) set trunk 5/1 desirable isl Port(s) 5/1 trunk mode set to desirable. Port(s) 5/1 trunk type set to isl. 5509-ER-F1> (enable) set module name 6 DevEng 100Mb Hosts Module name set. 5509-ER-F1> (enable) set port name 6/1 DE Sparc Ultra Port 6/1 name set. 5509-ER-F1> (enable) set port name 6/2-7 DE Sparc20 Ports 6/2-7 name set. 5509-ER-F1> (enable) set port name 6/8-12 DE NT Workstation Ports 6/8-12 name set. 5509-ER-F1> (enable) set port speed 6/1-12 100 Ports 6/1-12 transmission speed set to 100Mbps. 5509-ER-F1> (enable) set port duplex 6/1-12 full Ports 6/1-12 set to full-duplex. 5509-ER-F1> (enable) set port flowcontrol 6/1-12 send desired Ports 6/1-12 flow control send administration status set to desired (ports will send flowcontrol to far end if far end supports it) 5509-ER-F1> (enable) set port flowcontrol 6/1-12 receive desired Ports 6/1-12 flow control receive administration status set to desired (ports will allow far end to send flowcontrol if far end supports it) 5509-ER-F1> (enable) set port channel 6/1-12 off Port(s) 6/1-12 channel mode set to off. 5509-ER-F1> (enable) set trunk 6/1-12 off Port(s) 6/1-12 trunk mode set to off. 5509-ER-F1> (enable) set spantree portfast 6/1-12 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
5509-ER-F1> (enable) set module name 7 Corp/Mfg 10Mb Hosts Module name set. 5509-ER-F1> (enable) set port name 7/1-12 Corp Win98 PC Ports 7/1-12 name set. 5509-ER-F1> (enable) set port name 7/13-48 Mfg Win98 PC Ports 7/13-48 name set. 5509-ER-F1> (enable) set port duplex 7/1-48 full Ports 7/1-48 set to full-duplex. 5509-ER-F1> (enable) set spantree portfast 7/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
5509-ER-F1> (enable) set module name 8 DevEng 10Mb Hosts Module name set. 5509-ER-F1> (enable) set port name 8/1-48 DevEng WinNT PC Ports 8/1-48 name set. 5509-ER-F1> (enable) set port duplex 8/1-48 full Ports 8/1-48 set to full-duplex. 5509-ER-F1> (enable) set spantree portfast 8/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
5509-ER-F1> (enable) set module name 9 DevEng 10Mb Hosts Module name set. 5509-ER-F1> (enable) set port name 9/1-48 DevEng WinNT PC Ports 9/1-48 name set. 5509-ER-F1> (enable) set port duplex 9/1-48 full Ports 9/1-48 set to full-duplex. 5509-ER-F1> (enable) set spantree portfast 9/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
