CISCO路由器初始配置簡介

2019-11-05 00:56:12

字體：大中小

來源：轉載

供稿：網友

很多初學路由器知識的網友對路由器的初始配置可能感到很生疏,本人在初學時也很困惑,因為一下出來很多提問不知如何是好,下面將最近剛調試的一臺CISCO3640的初始配置整理出來與各位網友交流,如有疏漏之處,還請大家指正。

1.用CISCO隨機帶CONSOLE線,一端連在CISCO路由器的CONSOLE口,一端連在計算機的COM口。

2.打開電腦,啟動超級終端.為您的連接取個名字,比如CISCO_SETUP,下一步選定連接時用COM1,下一步選定第秒位數9600,數據位8,奇偶校驗無,停止位1,數據流控制無.最后選確定。

3.打開路由器電源,這時超級終端將出現以下畫面:

System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Copyright (c) 1999 by cisco Systems, Inc.C3600 PRocessor with 32768 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled

rogram load complete, entry point: 0x80008000, size: 0x4ed478 Self decompressing the image :

###################################################################

###################################################################

###################################################################

###################################################################

###################################################################

###################################################################

###################################################################

[OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

ubject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 16-May-00 12:26 by ccai

Image text-base: 0x600088F0, data-base: 0x60924000

cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.

Processor board ID 25125768

R4700 CPU at 100Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

8192K bytes of processor board System Flash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: y

您是否進入初始化配置對話,選Y

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.Basic management setup configures only enough connectivity

for management of the system, extended setup will ask you

to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: n

您是否進入基本配置安裝,選N

First, would you like to see the current interface summary? [yes]: y

首先,您是否看一下當前端口狀態

Any interface listed with OK? value "NO" does not have a valid configuration

Interface ip-Address OK? Method Status Protocol

FastEthernet0/0unassigned NO unset up down

Serial0/0 unassigned NO unset down down

FastEthernet0/1unassigned NO unset up down

Configuring global parameters:

Enter host name [Router]:RouterA

輸入路由器的名字

The enable secret is a passWord used to protect access to

rivileged EXEC and configuration modes. This password, after

entered, becomes encrypted in the configuration.

Enter enable secret: aaa

輸入密文

The enable password is used when you do not specify an

enable secret password, with some older software versions, and

ome boot images.

Enter enable password: bbb

輸入密碼(不能和密文相同)

The virtual terminal password is used to protect

access to the router over a network interface.

Enter virtual terminal password: ccc

輸入虛擬終端的密碼(以備遠程登錄)

Configure SNMP Network Management? [yes]: n

配置簡單網管嗎?選N

Configure IP? [yes]: y

配置IP嗎?選Y

Configure IGRP routing? [yes]: n

配置IGRP路由選擇協議嗎?選N

Configure RIP routing? [no]:

配置IGRP路由選擇協議嗎?選N

Configure bridging? [no]:

配置橋接嗎?選N

Async lines accept incoming modems calls. If you will have

users dialing in via modems, configure these lines.

Configure Async lines? [yes]: n

配置異步線路嗎?選N

Configuring interface parameters:

Do you want to configure FastEthernet0/0 interface? [yes]: y

您是否想配置fastethernet0/0接口?選Y

Use the 100 Base-TX (RJ-45) connector? [yes]: y

用RJ45的連接器嗎?選Y

Operate in full-duplex mode? [no]: y

選用全雙工模式?選Y

Configure IP on this interface? [yes]: y

在這個接口上配置IP嗎?選Y

IP address for this interface: 192.168.0.1

配置該接口的IP地址(在此地址為192.168.0.1

Subnet mask for this interface [255.255.255.0] :

配置該接口的子網掩碼.(默認的是255.255.255.0,可以手工輸入修改)

Class C network is 192.168.0.0, 24 subnet bits; mask is /24

Do you want to configure Serial0/0 interface? [yes]: y

您想配置serial0/0接口嗎?選Y

Some supported encapsulations are

/hdlc/frame-relay/lapb/x25/atm-dxi/smds

Choose encapsulation type [hdlc]:

選擇封裝方式(默認的封裝方式是HDLC,您可根據與您的路由器相連選用的封裝類型來決定用什么樣的封裝類型

No serial cable seen.

Choose mode from (dce/dte) [dte]:

(因為沒有連串口線所以會讓您選擇設備類型)

Configure IP on this interface? [yes]: y

(在接口上配置IP)

Configure IP unnumbered on this interface? [no]:

IP address for this interface: 172.16.0.5

配置該接口的IP地址(在此地址為172.16.0.5)

Subnet mask for this interface [255.255.0.0] : 255.255.255.252

配置該接口的子網掩碼.(默認的是255.255.0.0,可以手工輸入修改為255.255.255.252)

Class B network is 172.16.0.0, 30 subnet bits; mask is /30

(以下配置同上)

Do you want to configure FastEthernet0/1 interface? [yes]:

Use the 100 Base-TX (RJ-45) connector? [yes]:

Operate in full-duplex mode? [no]: y

Configure IP on this interface? [yes]: y

IP address for this interface: 172.16.0.9

Subnet mask for this interface [255.255.0.0] : 255.255.255.252 Class B network is 172.16.0.0, 30 subnet bits; mask is /30

The following configuration command script was created:

(把您的配置顯示出來)

hostname aaa

enable secret 5 $1$ul/V$ezbZFgvzGHD.YPSieC0Ew/

enable password RouterA

line vty 0 4

assword ccc

o snmp-server

!

ip routing

o bridge 1

!

interface FastEthernet0/0

media-type 100BaseX

full-duplex

ip address 192.168.0.1 255.255.255.0

!

interface Serial0/0

encapsulation hdlc

ip address 172.16.0.5 255.255.255.252

!

interface FastEthernet0/1

media-type 100BaseX

full-duplex

ip address 172.16.0.9 255.255.255.252

dialer-list 1 protocol ip permit

dialer-list 1 protocol ipx permit

!

end

以下提示您是否保存這次設置

[0] Go to the IOS command prompt without saving this config.

[1] Return back to the setup without saving this config.

[2] Save this configuration to nvram and exit.

Enter your selection [2]: 2

選擇2保存設置并存入NVRAM中

Building configuration...

[OK] Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started!

路由器重新啟動

00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down

00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up

00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down

00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down

00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

00:03:18: %IP-5-WEBINST_KILL: Terminating DNS process

00:03:24: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 16-May-00 12:26 by ccai

RouterA>

進入用戶模式

RouterA>en

Password:

RouterA#

進入全局模式

RouterA#sh run

查看現在運行的配置

Building configuration...

Current configuration:

!

version 12.1

ervice timestamps debug uptime

ervice timestamps log uptime

o service password-encryption

!

hostname RouterA

!

enable secret 5 $1$ul/V$ezbZFgvzGHD.YPSieC0Ew/

enable password bbb

!

memory-size iomem 25

ip subnet-zero

!

interface FastEthernet0/0

ip address 192.168.0.1 255.255.255.0

eed auto

full-duplex

!

interface Serial0/0

ip address 172.16.0.5 255.255.255.252

clockrate 2000000

!

interface FastEthernet0/1

ip address 172.16.0.9 255.255.255.252

eed auto

full-duplex

!

ip classless

o ip http server

!

dialer-list 1 protocol ip permit

dialer-list 1 protocol ipx permit

!

line con 0

transport input none

line aux 0

line vty 0 4

assword ccc

login

!

end