The following example shows a typical controller configuration for the multichannel E1/PRI port adapter on a Cisco 7200 series or Cisco uBR7200 series router:
2.Interface Configuration Examples接口配置舉例 The following example shows a typical interface configuration for the multichannel E1/PRI port adapter on a Cisco 7200 series or Cisco uBR7200 series router:
router> enable router# configure terminal router(config)# interface serial router(config)# interface serial 4/1:0 router(config-if)# encapsulation ppp router(config-if)# description ppp channel 5 router(config-if)# no shutdown router(config-if)# ^Z
3. Configuring Multichannel E1 Interfaces 配制多通道E1接口 The channel groups must be mapped before the multichannel E1/PRI controller can be configured. The following are controller commands used to map the channel group (the default variable is listed first):
controller E1 port-adapter-slot number/port-number (for Cisco 7200 series router) clock source [line internal] linecode [ami hdb3] framing [crc4 no-crc4] loopback [diagnostic local {payload line}] shutdown channel-group number timeslots list Number is the channel group 0 to 30. list is a number between 1 and 31. You can enter timeslots individually and separate them by commas, or enter them as a range separated by a hyphen (for example, 1-3, 8, 9-18). Timeslot 0 is an illegal configuration.
4.常用調試命令 show version or show hardware Displays system hardware configuration, the number of each interface type installed, Cisco IOS software version, names and sources of configuration files, and boot images show controllers Displays all the current interface processors and their interfaces show diag slot Displays types of port adapters installed in your system and information about a specific port adapter slot, interface processor slot, or chassis slot show interfaces type 0 or 1/ interface-port-number Displays status information about a specific type of interface (for example, serial) on a Catalyst RSM/VIP2 show interfaces type mod_num/bay/port Displays status information about a specific type of interface (for example, serial) on a Catalyst 6000 family FlexWAN module show interfaces type 3/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco 7120 series router show interfaces type 4/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco 7140 series router show interfaces type port-adapter-slot-number/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco 7200 series router show interfaces type 1/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco uBR7223 router show interfaces type 1 or 2/interface-port-number Displays status information about a specific type of interface (for example, serial) in a Cisco uBR7246 router show interfaces type interface-processor-slot-number/port-adapter- slot-number/interface-port-number Displays status information about a specific type of interface (for example, serial) on a VIP2 or VIP4 in a Cisco 7000 series or Cisco 7500 series router Router# show interfaces serial 3/1/0 show protocols Displays protocols configured for the entire system and for specific interfaces show running-config Displays the running configuration file show startup-config Displays the configuration stored in NVRAM
5. show Cisco 7200 Series and Cisco uBR7200 Series Routers 下列顯示72的SHOW結果！
Following is an example of the show interfaces serial port-adapter- slot-number/port-number:channel-group command for Cisco 7200 series and Cisco uBR7200 series routers. It shows all of the information specific to the first multichannel E1/PRI port (port 0) in port adapter slot 2, channel group 1:
Router# show interfaces serial 2/0:1
Serial2/0:1 is up, line protocol is up (looped) Hardware is Multichannel E1 Internet address is 1.6.0.1/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) Last input 00:00:07, output 00:00:07, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0 (size/max/drops); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/64/0 (size/threshold/drops) Conversations 0/1 (active/max active) Reserved Conversations 0/0 (allocated/max allocated) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 87 packets input, 6521 bytes, 0 no buffer Received 87 broadcasts, 0 runts, 0 giants 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 87 packets output, 6521 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 1 carrier transitions no alarm present Timeslot(s) Used:1-31, subrate: 64Kb/s, transmit delay is 0 flags
