相應peng的號召，所以我起了這個名字的主題。但是不知道是否經典：） 首先是文件系統方面 How to Download a Software Image to a Cisco 2600 via TFTP Using the tftpdnld ROMMON Command
This document eXPlains how to download a software image to a Cisco 2600 using Trivial File Transfer PRotocol (TFTP) over the first LAN port using the tftpdnld ROMMON command.
Notes:
* The ROMMON TFTP transfer works on the first LAN port only; however, for the Cisco 2612, you can choose the Token Ring or Ethernet port.
* You can only download files to the router. You cannot use ROMMON TFTP to get files from the router.
* Does not support source route bridging on Token Ring ports.
The variables to set for tftpdnld are shown below:
usage: tftpdnld Use this command for disaster recovery only to recover an image via TFTP. "tftpdnld" has no arguments. Monitor variables are used for arguments. (Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.) "ctrl-c" or "break" stops the transfer before Flash erase begins.
The following variables are REQUIRED to be set for tftpdnld: IP_ADDRESS: The IP address for this unit IP_SUBNET_MASK: The subnet mask for this unit DEFAULT_GATEWAY: The default gateway for this unit TFTP_SERVER: The IP address of the server to fetch from TFTP_file: The filename to fetch
The following variables are OPTIONAL: TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=7) TFTP_TIMEOUT: Overall timeout of operation in seconds (default=2400) TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1) rommon 14 >
The variables to set for Token Ring are shown below:
TR_1E1R_PORT On the Cisco 2612, this variable sets the Token Ring or Ethernet port. 0 = use Ethernet port 1 = use Token Ring port Default is 0 TR_SPEED_MODE For a Token Ring port, this variable sets the ring speed and duplex mode. 0 = 4 Mbps half-duplex mode 1 = 4 Mbps full-duplex mode 2 = 16 Mbps half-duplex mode 3 = 16 Mbps full-duplex mode Default is 2
The variables to set for Fast Ethernet are shown below:
Invoke this command for disaster recovery only. WARNING: all existing data in all partitions on flash will be lost! Do you wish to continue? y/n: [n]: y
Receiving c2600-is-mz.113-2.0.3.Q from 171.69.1.129 !!!!!.!!!!!!!!!!!!!!!!!!!.!! File reception completed. Copying file c2600-is-mz.113-2.0.3.Q to flash. Erasing flash at 0x607c0000 program flash location 0x60440000 rommon 22 >
How to Download a Software Image to a Cisco 2600 through the Console Port Using the xmodem ROMMON Command
You can download a software image to a Cisco 2600 through the console port using the xmodem [-cyr] [filename] ROMMON command, where:
* -c specifies CRC-16
* -y specifies YMODEM protocol
* -r copies the image to RAM. (It does not copy to Flash. Leave off the -r to copy the image to Flash.)
Notes:
* The ROMMON XMODEM/YMODEM transfer works on the console port only.
* You can only download files to the router. You cannot use XMODEM/YMODEM to get files from the router.
Example
rommon 1 > xmodem -c c2600-is-mz.113-4.T1 Do not start the sending program yet... File size Checksum File name 4466148 bytes (0x4425e4) 0x7a90 c2600-is-mz.113-2.0.3.Q
WARNING: All existing data in bootflash will be lost! Invoke this application only for disaster recovery. Do you wish to continue? y/n [n]: y Ready to receive file c2600-is-mz.113-4.T1 ... Erasing flash at 0x607c0000 program flash location 0x60440000 Download Complete! program load complete, entry point: 0x80008000, size: 0x4412cc Self decompressing the image : ################################################]
