maui-slt-01#show running-config Building configuration... Current configuration: ! version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service passWord-encryption ! hostname maui-slt-01 ! aaa new-model aaa authentication login default local aaa authentication login NO_AUTHEN none aaa authentication ppp default local
!--- This is the basic AAA configuration for PPP calls.
!--- Defines username for remote router (maui-nas-03) and shared secret password. !--- Shared secret(used for CHAP authentication) must be the same on both sides.
!--- Sets up chat script "Dialout" used for the dialout connection on aux 0.
modemcap entry MY_USR_MODEM:MSC=&F1S0=1
!--- Modemcap (MY_USR_MODEM) will be applied to the AUX port line interface !--- This modemcap was created using the command: !--- modemcap edit MY_USR_MODEM miscellaneous &F1S0=1 !--- Refer to the Modem-Router Connection Guide for more information.
! interface Loopback0 ip address 172.17.1.1 255.255.255.0 ! interface FastEthernet0/0 ip address 172.16.1.1 255.255.255.0 no keepalive duplex auto speed auto !
! <<-- irrelevant output removed
! interface Async65
!--- Async interface corresponding to the AUX Port. !--- This was determined using the show line command. !--- See External Modem Setup and Troubleshooting Tasks for more details.
no ip address encapsulation ppp
!--- Use PPP encapsulation over this link.
dialer in-band dialer pool-member 20
!--- Designate Async65 as member of dialer pool 20. !--- The command dialer pool 20 is specified in interface Dialer 10.
async default routing
!--- This permits routing over the async interface. !--- This is required for a routing protocol to run accross the async link.
ppp authentication chap callin ! interface Dialer10
!---Dialer 10 is the logical interface for Dialer Pool 20.
ip unnumbered Loopback0
!--- Uses the Loopback 0 IP address.
encapsulation ppp ip ospf demand-circuit dialer remote-name maui-nas-03
!--- Specifies the remote router name. !--- This name must match the one used by the remote router for authentication
dialer pool 20
!--- Async 65 is a member of this pool
dialer idle-timeout 900 dialer string 81690
!--- Defines the destination router's phone number
dialer max-call 4096 dialer-group 1
!--- apply interesting traffic definition from dialer-list 1
ppp authentication chap callin
!--- Use CHAP authentication for incoming calls
! router ospf 5 network 172.16.1.0 0.0.0.255 area 0 network 172.17.1.0 0.0.0.255 area 0 network 172.22.1.0 0.0.0.255 area 0
!---OSPF is used between the routers. !---A routing protocol is unnecessary if you configure the appropriate static routes.
! ip classless ip route 0.0.0.0 0.0.0.0 Dialer10
!--- Default route points to int dialer 10. !--- This is necessary since OSPF is not configured to send default routes.
no ip http server ! access-list 101 remark Define Interesting Traffic access-list 101 deny ospf any any access-list 101 permit ip any any dialer-list 1 protocol ip list 101
!--- Use access list 101 for interesting traffic definition !--- This is applied to interface Dialer 10 using dialer-group 1
! line con 0 login authentication NO_AUTHEN transport input none ! line aux 0
!--- line interface for the AUX port
exec-timeout 0 0
!--- disable exec timeout on the interface
script dialer Dialout
!--- use chat script "Dialout"
modem InOut
!--- enable incoming and outgoing calls
modem autoconfigure type MY_USR_MODEM
!--- apply the modemcap MY_USR_MODEM that was configured previously
transport input all stopbits 1
!--- Improve throughput by redUCing async framing overhead
speed 115200
!--- The AUX port on the 2600 supports a speed of 115200. !--- Note: If you are routing through the AUX port, each character generates a !--- processor interrupt. This is an abnormally high load on the CPU, which can be !--- resolved by using a lower AUX port speed.
flowcontrol hardware
!--- configures RTS/CTS flow control
line vty 0 4 ! no scheduler allocate end
maui-nas-03 (5300)
maui-nas-03#show running-config Building configuration... Current configuration: ! version 12.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname maui-nas-03 ! aaa new-model aaa authentication login default local aaa authentication login NO_AUTHEN none aaa authentication ppp default local
!--- This is the basic AAA configuration for PPP calls.
