2514#sh run Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service passWord-encryption ! hostname 2514 ! enable password cisco ! ip subnet-zero ! ! PRocess-max-time 200 ! interface Ethernet0 ip address 203.93.188.51 255.255.255.224 no ip directed-broadcast ip nat outside no ip mroute-cache ! interface Ethernet1 ip address 10.10.10.1 255.255.255.0 no ip directed-broadcast ip nat inside no ip mroute-cache ! interface Serial0 no ip address no ip directed-broadcast no ip mroute-cache shutdown ! interface Serial1 no ip address no ip directed-broadcast no ip mroute-cache shutdown ! ip nat pool test 203.93.188.51 203.93.188.51 netmask 255.255.255.255 ip nat inside source list 1 pool test overload ip classless ip route 0.0.0.0 0.0.0.0 Ethernet 0 access-list 1 permit 10.10.10.0 0.0.0.255 ! line con 0 transport input none line aux 0 line vty 0 4 password cisco login ! end 2514#ping Protocol [ip]: Target IP address: 203.93.188.51 Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands [n]: y Source address or interface: 10.10.10.10 Type of service [0]: Set DF bit in IP header? [no]: Validate reply data? [no]: Data pattern [0xABCD]: Loose, Strict, Record, Timestamp, Verbose[none]: Sweep range of sizes [n]: Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 203.93.188.51, timeout is 2 seconds: 00:20:06: NAT: o: icmp (10.10.10.1, 3472) -> (203.93.188.51, 3472) [5] 00:20:06: NAT: i: icmp (10.10.10.1, 3472) -> (203.93.188.51, 3472) [5] 00:20:06: NAT: address not stolen for 10.10.10.1, proto 1 port 3472 00:20:06: NAT: failed to allocate address for 10.10.10.1, list/map 1. 00:20:08: NAT: o: icmp (10.10.10.1, 3473) -> (203.93.188.51, 3473) [6] 00:20:08: NAT: i: icmp (10.10.10.1, 3473) -> (203.93.188.51, 3473) [6] 00:20:08: NAT: address not stolen for 10.10.10.1, proto 1 port 3473 00:20:08: NAT: failed to allocate address for 10.10.10.1, list/map 1. 00:20:10: NAT: o: icmp (10.10.10.1, 3474) -> (203.93.188.51, 3474) [7] 00:20:10: NAT: i: icmp (10.10.10.1, 3474) -> (203.93.188.51, 3474) [7] 00:20:10: NAT: address not stolen for 10.10.10.1, proto 1 port 3474 00:20:10: NAT: failed to allocate address for 10.10.10.1, list/map 1. 00:20:12: NAT: o: icmp (10.10.10.1, 3475) -> (203.93.188.51, 3475) [8] 00:20:12: NAT: i: icmp (10.10.10.1, 3475) -> (203.93.188.51, 3475) [8] 00:20:12: NAT: address not stolen for 10.10.10.1, proto 1 port 3475 00:20:12: NAT: failed to allocate address for 10.10.10.1, list/map 1. 00:20:14: NAT: o: icmp (10.10.10.1, 3476) -> (203.93.188.51, 3476) [9] 00:20:14: NAT: i: icmp (10.10.10.1, 3476) -> (203.93.188.51, 3476) [9] 00:20:14: NAT: address not stolen for 10.10.10.1, proto 1 port 3476 00:20:14: NAT: failed to allocate address for 10.10.10.1, list/map 1. SUCcess rate is 0 percent (0/5) 2514# 大家看看我這個配置有什么問題。 我在終端配了10。10。10。10 PING 203.93.188.51 總是不行。
